WANTED: Complete power steering setup for my 1964  P code Galaxy convertible with 4 speed.  Owned car for 40 years and at
one time manual steering was sufficient.  Now,  need a little help!

FOR SALE: 1961 tbird 390 engine-not seized. Comes complete with exhaust manifolds,intake manifold with new 4 barrel, auto
trans. Water pump & pulleys.$1000.00 obo call (519-941-4247. Anytime

WANTED: Looking for a 406-427 solid lifter cam. I have a  few P/N C3AZ-6250-AA or D.  306 duration, 500 lift. New or good used  
thanks. send email if you have.  Bill

FOR SALE: 1963 427 cast iron exhaust manifolds mint condition, 2x4 intake. $3000 or best offer. Bare "J" code heads $900.
Please call Ryan 360-929-3258

FOR SALE: 1962 Galaxie 500/XL 406 Hardtop for Sale. Original CA G-Code Hardtop. Fresh restoration with approximately 150
miles. Black exterior with red interior. Professional base coat/clear coat paint. Body better than new. 500 trim left off of exterior but
have it. Rebuilt seats (power drivers), carpet, dash, door trims, headliner, console... Professionally built stroker tripower engine
with rebuilt 64 Toploader (big input/output). 4:56 posi. New springs, shocks... Freshly re chromed front bumper still to be installed.
Re chromed die cast, NOS parts all over this car. Tri-Y headers with 3" custom mig welded exhaust with Borlas and inside controlled
cutouts. Tinted glass. New windshield and completly new rubber seals. To much to list.  Was building it to Nostalgia race, but
changed priorities. Reduced to $40,000 or best offer (possible partial trade) Number 517 on 1962 Galaxie registry.  

FOR SALE:  Ford Galaxie 427 Exhaust Manifolds. I have a pair of Cast Iron Factory 427 Galaxie manifolds. Sad to say they have
been repaired (welded), can text pictures. #’s C5AE-9430 H & C5AE-9431 C, code 8 26 4 & 3 20? I will sell to the best offer.
Located in Northern California. Brad (707) 235-2556.

FOR SALE: Unassembled 427 cross bolt main engine block from 1963 1/2 Galaxie 500, bored .30 over and stroked w/ 428 crank =
454ci with unused 12.5 to 1 TRW aluminum pistons and Ford Le Mans Connecting Rods, still in original FMC boxes. Dual-Quad
aluminum intake with 2 Holley 652cfm carbs, Toploader 4speed Transmission, Lakewood bulletproof bellhousing & block-saver
plate, 427 heads, 428 cobra jet heads, aluminum open headers, water pump, oil pan, and several cam and crankshafts (390, 427,
428). Ford 9” rear end with 5.67 gears. Cylinders are greased up and in great shape. Pictures and information available upon
request. Contact Steve by text or call at: 608-338-8090 (WI) or  $15,000 or best offer.

FOR SALE: 1964 Galaxie 427 toploader. HEH-H.  big input. Looks like new inside and feels smooth. exterior very rusty, including
input shaft. Tag barley readable. email for pics. no shifter. $1500 firm.

WANTED: for factory 1963 Ford  Galaxie 500 Lightweight 427 drag car:  original used or remanufactured FRONT aluminum bumper
brackets right and left. If I could get pictures of any aluminum brackets that would be appreciated. I may have to make my own set !
Please contact : Robert Larson  cell: (218) 251-6928  

FOR SALE: 1963.5 Galaxie 500 XL  R-code black on black ,the good,,, very nice body, paint [ discounting  A scratch and years
worth of dust] and most of the interior, original wheels it has power windows and power drivers seat. vintage Sun  tach.non original
2.5 custom exhaust.the bad not original 427 marine block [ with correct heads, intake, exhaust manifolds and dist, looks correct
under the hood.] no original T-10,[has a fresh toploader with Hurst] needs headliner  wheel covers and bumpers restored , this is my
long term project that has not been worked on in years, mechanically it was in  great.running condition when parked has fresh paint
and needs the trim installed and now needs the tank drained and what ever you feel is needed after not starting in 7 years [it does
turn]   all trim is present along with some spares and Traction Master Monster traction bars please contact Bruce Dodds at        

FOR SALE: 1965 427 lowriser intake and carbs.  Matched, original pair BJ/BK dated 492.  C5 intake dated 8-64.  Original linkage,
log, and air cleaner bottom.  Missing secondary vacuum pods and choke.  No other carb or intake mods.  Everything works and
moves.  No corrosion.  Nice looking stuff. $3000.  Pictures available.  Chris.  513-907-1931.  

FOR SALE: Finally available.  Reproduction 15" KH Hipo wheels.  These are new and extremely nice.  Cat eyes are identical.  Has
safety hump in bead seat area identical to 5.5 hipo wheels.  Available in widths 5-8 and 10".  $300 ea.  Pictures available.          
Call Jack at Jacks Automotive.  812-265-4342.

SOLD!!!  Complete late 1963 low riser 427 top oiler . C4AE-6015A- 3M21 , December 21, 1963 , Heads 5/27/63 C3AE . Aluminum
intake 1-4 Barrel . Original sheet metal . Never been bored but has been honed only . Heads and block have been Magnaflux and
checked by certified machine shop .

WANTED:  Early-1965 427 Sideoiler block, casting number, C5AE-G.  Prefer either an N.O.S. unit or one that was never seriously
damaged, has no sleeves and is still usable at standard bore, but all will be considered.  Will pay cash and pick up.  Tel: (386) 734-
4026.  E-mail:

WANTED: 1967 Galaxie XL 427 car R or W code in any condition. Must be an XL model Contact

SOLD!!! complete ready to install 427 sideoiler for sale. 1966 block,63 lowriser heads and intake. Steel crank and lemans rods.
New bearings and rings. There is a video available of the engine running

SOLD!!! Very Rare 1962 HIPO M-code Galaxie Sunliner convertible (390-401hp) tri-power , 4 speed, power windows, power
bench seat, rear mount antenna, spotlight, tinted glass, padded dash. Kelsey Hayes wheels, big brakes and Heavy Duty
Suspension, Rare special order DSO (Domestic Special Order) car. 2 build-sheet car, Built Nov 27, 1961 Los Angeles plant, Car
has been off the road since 1969, 68,xxx miles, Missing the original engine and trans currently has non running 63 390 no trans in
the car. Have all the trim, grill, front bumper. It is a serious project that needs complete restoration. Pictures available, serious
inquires only.

SOLD!!!: Have a rebuilt 352 cu with a 4 barrel carb and 3 speed, Cruise-o-matic transmission for sale. This combo is still in my car
and I will not remove it until it is sold so that the buyer can see how it runs and if need be, drive the car so he knows what he is
getting. Looking to get $3500 and you pay for removal and cartage. Also have a 1964 Galaxie 500, 4 door sedan for sale. Good
glass except for front windshield (cracked), all chrome wrapped and labelled, both bumpers, re-cored radiator, and much more.
Have all bills to prove what was purchased. Looking for $3900 OBO. Note: Car has no engine unless you want to purchase engine
and transmission with sedan, then we can work out a great price for everything. Car and engine located in Edmonton, Alberta.
Please email me for details and phone number

FOR SALE: parting  or whole 1962 Ford Galaxie 2 dr ht 352 stick rusty  underneath, great trim and all stick parts present. very
original decent bumpers thanks Bruce  732-363-1839

FOR SALE: 61 starliner body, has 62 fenders on it, comes with 61 fenders, good parts, restorable car, has a 3 speed column, has
some other chrome that is not in pic's, asking 3000. Has Georgia bill of sale. Call 352-216-2273

FOR SALE: 1965-67 Ford 427 Medium Riser Head, It is in very good condition and has never had a valve in it. It is a bare casting
with no porting or repairs. Ford #C5AE-F, Dated 5E6, asking 1200. Also have a low 1963 Ford 427 Low Riser Head  It is in very
good condition. It is a bare casting with no porting or repairs. Ford #C3AE-6090-H Dated 3D19, Asking 700. Also a 1961-63 Ford
Galaxie Shorty Header Exhaust Manifolds They are both in very good condition with no welds or repairs.Originally came off a low
mileage car. Ford #C1AE-9431-C,Dated F142 & F152 asking 1000. Call 352-216-2273 Or

FOR SALE: 1962 Ford 406 Standard Bore High Performance Block & Grooved Crankshaft. It is in very good condition and is still
standard bore with 4 thousandths wear in the cylinders. It has the HP on side and the back of the block. Down inside, where the
extra webbing is, it has HP there also. The block was never abused or raced and has been protected with cosmoline. Includes free
grooved crankshaft, (the mains are grooved for extra oiling). It is turned 0:10. Keyway will need to be repaired, (see pictures). Ford
#C2AE-6015-J, Dated 2D18, Crankshaft part #C3AE-E $2100.00  We also have a 1962 SE 406 Heads, Rods, Shorty Headers, Tri-
Power Intake.Email or call 352-216-2273.

FOR SALE: 427 Medium Riser Holman Moody intake excellent condition (may be NOS) I have had it for 30 years and never seen
another. I'll take $2000,00 or best offer.

WANTED: 65 galaxie 500 xl convertible top switch….must be in good working condition…Rick   250-793-8366

FOR SALE: 1966 R code Galaxie. Listed in this registry. Runs and drives, engine has less than 1000 miles since rebuild rest of
driveline good. Put disc brakes on the front, but have all original equipment still. Exterior and interior completely original unrestored.
NO RUST. Car has spent its life in CA and AZ. I am the third owner. Need someone who has the time, money and will to complete
it. So much more, can send photos. contact me at  I'm aware of the rarity and value and will not give it
away, but will be fair in discussing offers. Check NADA for a starting point.

WANTED: A nice driver quality 1963 Galaxie 500 Convertible.  Older restoration or nice survivor would work.  Would prefer 390, but
am open to other offers. Contact Bob at

FOR SALE: A set of nos 427 valves the exhaust ones are sodium cooled and open to offers asking $500 email or call/ text

WANTED: 63 Galaxie Light Weight Bostrum Front Seats also always looking for Kelsey Hayes 15x5.5 Hi Po steel wheels
call Pete 302-242-6801 email

FOR SALE: 427 marine block dated 1966, STD. bore, Block has been tanked and crack checked, New cam bushings and oil relief
valve and spring, cast as side oiler, drilled as a center oiler with relief valve above cam, also included is the piston and rods out of
this block, $2500.
Also have a 427 service block 1972 date code,it is a side oiler block it is .030 over, has 8 sleeves and needs at least 2 sleeves
replaced, all caps and spacers included,  $400.
C1AE-A heads cut for big valves  $300.  Call or text Dave at  570-809-4474   Located in central Pa. 17860 I cannot ship

SOLD!!! Ford Galaxie 427 Exhaust Manifolds. I have a set of Cast Iron Factory 427 Galaxie manifolds for 63’-64’ Galaxie Q or R
code 427. These are almost NOS.. They were on the shelf for 40 plus years. They are date coded March/April of 1963. No repairs.
No broke ears/tabs. $1250.00 plus the ride.

FOR SALE: 1963 Ford Galaxie 500 R Code Original Never Restored Mint Condition. Everything is original, Everything is Flawless.
Sounds and smell great. You are looking at an original vehicle with original miles. I have many documents I can send you with this
one. Call Ryan Hansen at 224-944-4534 or email

SOLD!!!1972 351 Cobra Jet, block (4 bolt) #D2AE-BA date 2C18. engine is apart. rebuild has been started. bored +30, crank 10-
10, very many new parts for the build. pictures on request.

WANTED: 64 427 block or short block looking for j or k (September or October) of 63

WANTED: Air Cleaner FE Hipo style, Single carburetor, Chrome double hump open element style. For a single carb 427.  send pics
to email or call 250 306-9445

FOR SALE: 63.5 Galaxie 500xl 390 auto p/s power disc brakes. Factory air blows cold. Rangoon red with black interior. very
straight body one repaint in 1988, original color. Great running driving car. Asking $19,500.00. e-mail with any questions.

WANTED: 1, 2, 3 or 4 Kelsey-Hayes 15 x 5.5 steel wheels for Hi-Po Galaxie.  Or, 4 Kelsey-Hayes 15 x 5 steel wheels which have
the cutouts exactly like the 15 x 5.5 wheels. Mark Carswell 704-616-7324

FOR SALE: "RARE" 1962, 1963 and 1964 Galaxie Lightweights. Formerly the Rick Kirk Collection. The barn find of all barn finds.
The 1962 is the one with the SOHC in the magazines. The 1963 is half way finished. The cars have not been run for 30? years?.
Have lots of documents, magazines and pictures. These are believed to be the only collection in the World with all three years. I will
not send a bunch of pictures so you can make a fake lightweight. $400,000 I will not breakup the collection. Email me with questions . These cars are in Bend, Oregon.

WANTED: I am looking to buy a 1963 ½  R code Galaxie. I would like a restored car but would consider one needing a little work. I
am a serious cash buyer. I bought one new in 63 & would like to have one again. I collect chrome bumper Corvettes 63/72 & would
consider a trade. Looking for a REAL R code  with all the matching date codes & #’s
KEN BARRY  260 927 6891

WANTED: 1963 ford 427 long block. Must be date coded before April 63. Will buy complete engine or parts. Block. C3AE-6015-AB
Heads C3AE-6090-D (G,H,J IF early date) distributor C3AF-12127-AE THANK YOU. I can be reached at
com Or by phone 704-219-6098 Jeff.

SOLD!!!: TWO ENGINES...1966 427 Side Oiler 2x4 bbl, Medium Riser heads with The special Ford $ crank, Le Mans rods and
Pro Forged HD racing pistons, bored .030 over and race prepared. Full race...$10,000
1967 427 center oiler 2x4 bbl dual 550 Holly chrome carburetors, Medium Riser heads ported and polished, titanium valves 250 lbs
springs, MSD distributor, billet pulley's....and lots more.... Built for street-race and show, would look good in your Cobra, Fairlane,
Comet, Galaxie or show project car! ... with old school power 550+ hp...with high cross flow rad, 4-spd, long tube headers.(for '67
Mustang) street ready...$15,000
Both motors are 550hp, complete with dual carbs, and have been balanced - blueprinted, professionally built.

WANTED:  A set of 427 /390 galaxie long tube headers in good shape with no major repairs or modifications contact:

WANTED: Ford fe 427 medium riser heads, c5ae-f. looking for c5ae rocker arm steel stands assembly.

WANT TO TRADE: I have c3ae9525-k intake in excellent condition want to trade for c3ae9525-j in same condition also looking for
c3ae9510c carbs and linkage for dual 4s John 602-549-6611 email

WANTED: Single four barrel Holman Moody intake manifold for the FE low or medium riser.  I've been looking everywhere with no

FOR SALE: 63 ford galaxie 2dr fastback 500 XL, 352, automatic, X code, complete, rust free solid car found in Arizona. Currently
located in southern AZ, I am able to deliver for the right deal. $8,000     call 520-235-9564 or text 602-281-5131

SOLD: 1964 427 high riser carb, c4af-9510-da. date 661, pri. block 4137, sec. block 4241. all throttle plates 172. taken off my Q-
code 64. pictures on request. $650

WANTED:  Top dollar paid for a C5AE-6007A center oiler block with a 4J date code. Call or email Mark at 603-642-8144 or

WANTED: Correct front seats for a 64 Lightweight. Contact Eric @

FOR SALE: C3AEH heads date 3G9 & 3E16. have matching  adjustable rocker arms, solid lifters and pushrods from same engine.
also have a couple of factory ford solid lifter camshafts found at the same auction. AB & ABA with backwards letters. the previous
owner had order the cams new from ford and the camshaft shipping tubes were on a wagon during sale. also have a C3AE AE
distributor from same sale date 3LB. the heads, distributor, and rocker arms have been cleaned up. i can send you pictures of
anything you have an interest in. i would prefer to keep the parts together. for the heads , rocker arms, drip rails, pushrods, AB
camshaft with matching solid lifters $1200. the distributor is priced at $350. the ABX solid lifter camshaft and solid lifters is $150.
thanks. eudora ks. 785-542-1000. jim oberg

WANTED: 1964 R code 427 engine complete or parts dated sometime in March 1964. Please email

SOLD!!! These are bare pair of 427 H heads dated July 9th and 10th of 1963. I just had these heads totally gone over for cracks
and damage. They needed very minor repairs that were mainly cosmetic and would have run fine without them but I wanted them
right. Once repaired they were pressure tested and were perfect. They will need to be totally rebuilt and should have one guide
installed in one of the heads since the top has chipped off. Basically they are perfect cores for rebuilding especially if your looking
for a set with these date codes.

SOLD!!! A Complete 427 Ford FE Motor. 4 bolt center mains. Has 2, 4 barrel Holley Carbs. All matching numbers, including, block,
heads, Carb. intake, etc. (C3AE). Has a Ford aluminum 8V intake. Eng. was dissembled, cleaned, installed new gaskets & ran.
$8000.00. Negotiable. Serious inquiries only

WANTED:  Original ford aluminum single four intake manifold with date code prior to March 6, 1963 and after January 6, 1963.  Call
Bob Kelley at 805 402 3124.

FOUND!! pair of 65, 427 cast iron headers. Must be in good condition.  

SOLD!!! 427 low riser heads and intake. Includes rocker shafts, oil baffle, valve covers. Heads have some cracks, machine shop
States repairable. Intake c3ae-9425-k. Heads c3ae H 6090H $700 firm for all please contact

WANTED: Looking for a nice set of white door panels for my 1964 Galaxie 500xl Q code fastback.  Please call. 818-601-0055

SOLD!!! 1964 427 high riser carb (single 4-v) C4AF-9510-AD, LIST 2919, DATE 661, PRI. BLOCK 4137, SEC. BLOCK 4241, ALL
THROTTLE PLATES 172.    Taken off running engine two years ago (my Q-code 64) pictures on request.

WANTED:  1965,66,67 ford Galaxie 427 "R" or "W" code, any condition.  Bill  @

FOUND!!! 427 Dual Quad  high riser Intake please contact

FOUND!!! 63 Galaxie 4 speed reverse light switch. Needs to be nice operating OEM or NOS part. Please contact:

SOLD!!! Original 427 Valve Springs and Spring Cups. The Springs appear to be unused,no Oil residue on them and still have
the primer Red Color to them $150

SOLD!!!  Pair of Low Riser C3AE-6090-H, date coded 3E16 and 3E7 the one head is complete,Valves,Springs,Cups and Retainers.
The other head has the Four Intake Valves and only Exhaust valves,appear to be original Ford Valves. Would like to sell as a pair,
but if someone is in need of just one I would seperate the H heads to help the cause. $600

FOR SALE;  Pair of Low Riser C3AE-6090-D, casting dates 3B7 and 3B11, complete with Valves,Springs,Cups and Retainers.They
have lots of meat on them and they have been marked that they have been magnafluxed "OK",not by me however. $800 Please

SOLD!!! 1964 “Q” code Galaxie XL. This car is not a rust bucket but every panel including the roof is dented. It will need both
quarters, roof and front sheet metal the radiator support was cut and there is no running gear other than front drums and
suspension. The rear 6 leaf springs and housing with no 3rd member are in car. Basically I’m selling a platform to build a Q code
car. The vin is on the cowl in 3 places and drivers door with the tag on it. Original color is a dark metallic blue with silver top and
Blue interior.

WANTED: Looking for a frame to fit my 2 door 1966 Ford Galaxie 500 XL. Also needs rear quarters, both sides. Call  Russell at
603-216-4206 or email at

WANTED: 1963 or 1964 Galaxie 500 XL R code. Prefer in restored condition but would consider a restorable car as long as all
components are there. Please contact Bob Hansen or call 608 201 3988.  

SOLD!!!! Q Code Spingtime Yellow 1966 Galaxie 500 428 w/Auto trans. Power steering and A.C.. This car was an Arizona car and
relocated to Texas in 1994. The car is currently not running. Haven't had time to mess with the engine. I was lucky to find a build
sheet in the rear seat. This has black interior with a floor console. Could use front seat covers. Has the original engine, heads,
intake, manifolds, trans, rearend. Engine casting numbers and date codes match the cars build date. The front suspension, brakes
and lines have been replaced. Very little rust. Floors are great as is the frame. The rear diff tag is still on the housing 3.25 gear. It
has all 4 of the hub caps. This car is ready for a restoration and for the most part is complete. For info on the vin and data tag
please email.. This vehicle has a clear title. Asking $5,500.00 OBO. Located in Houston, Tx. Area.

WANTED: 1963 427 2 x 4 low riser intake. Please call Greg at 989-845-2699. Thank you. 3/12/13

SOLD!!!!! Front and Rear Bumperettes for a 1963 Galaxie. These are super nice originals that look like they have never been on a
car but I'm sure they had to be at some point. They have a few scratches from sitting around but the chrome is in excellent condition
along with the rubber bumper pads. $450 for the set of 4 email

WANTED: Ford 427 side oiler block C5AE-D code, 1965 casting date. With or without crank/internals
contact Paul on +44 (0) 7710 425177. Collection from any US or UK location is possible.

WANTED: Clutch fork for a 1964 galaxie with the 1 3/8 toploader input. Call Carl at 620-491-1375 or email

WANTED:  I am looking for a 63 ford trunk lid for my Q code galaxie.  Need one with little or no rust and no repaired damage.  I will
worry about the shipping. Bob 805 402 3124

WANTED: 1965-69 Ford Galaxie or Mercury Monterey or Marquis bucket seats in decent shape, minor repair needed OK, Must be
lowbacks with separate headrests. Prefer Black or Green but will consider other colors . Must be out of fullsize car.    send pics,
price and location.  Kenny. ad placed 12/25/12

FOR SALE: I have an excellent working 6-way power bench seat setup for any fullsize Ford or Merc.. This was pulled from a 1969
LTD but will fit all Ford Galaxies and Mercury's and other years as well. Genuine Ford with motors,seat brackets, cable, wiring and
switch assembly. Just add your own seat. This would make a nice comfort 6 way adjustment addition to your existing manual seat.  
$150.00 OBO plus shipping.  Will take Cash on pickup, PayPal or Postal Money Order   Kenny. ad placed

SOLD!!!: 1969 FE 390 long-block engine, pulled from 1969 Ford Galaxie, runs, has no knocks or leaks but blows a puff of blue
smoke when first started up after sitting and has a noisy lifter, probably needs to be rebuilt. Comes with good C-6 Automatic tranny.
$750.00 OBO for both or trade for FE-390 tri-power setup.  sell or trade, need space in garage for my other Galaxie. Chicago
area. Kenny. ad placed 12/25/12

WANTED: 1965 Custom 500 , 2 door post , 427, 4 speed, (a clone is acceptable if done correctly), prefer a white car.   contact by
email   ;

FOUND!!! 427 low riser heads C3AE-6090-D with an early February date code.

WANTED: Iron 427 Low Riser heads in good condition. Best date codes late 1964 (4K_,4L_).email:

WANTED:  Four (4) K-H rims for a 63 1/2 R code

SOLD!!! I have a very rare option - '61-'62 manual 4 way seat adjusters for sale. $100.00.

WANTED: Cast iron exhaust headers that will fit a 390 in a 1968 Galaxie 500 2door. The ones from 64 and earlier do not fit , and I
have a mint condition set of 1962 Galaxie headers  part # C1AE-9431 A&B .Email me at , or phone 306-662-
3312, ask for Ed

SOLD!!!  1963 1/2 Galaxie body for sale. No doors, deck lid, or front end. Wheel housings solid.

SOLD!!  An excellent 1964 Ford Galaxie transistorized ignition relay box from wheelhouse. Looks great and from old Ford race
shop. Looking to get $750 for it.

WANTED: Two NOS Goodyear Power Cushion 8.15 X 15 tires.  Call 864-270-7130 or email   Have two and
need two more. Any leads would be appreciated.

SOLD!! Rotunda 8000 RPM Faria Tach with cup and bracket that has been restored and looks new, never got around to using it. It
was restored by Phil Severance(Phidon Restorations). $475 plus shipping

FOR SALE: 1967 Ford Country Squire (six passenger)  390-2V Special Brittany Blue; 3.00 standard axle ratio; Visibility Group;
Tinted Glass; Power Disc Brakes; factory A/C 71E Q 6B 10D 15 1 U Car located in Pleasantville NY; registered & NY State
inspected for 2012. Solid example of classic design Car needs some work around the driver side rear wheel opening; otherwise
clean. Spent most of its life in dry Utah. This fall the car will appear in a Vogue pictorial with Kristen Stewart and the cast of “On-
The –Road”, photographed by the classic fashion photographer Peter Lindbergh. For photos, e-mail or call Bill Lenihan 914-610-
9325 or email

SOLD!!!  NOS pair of Ford cast iron long tube headers for 427 ci engine. Casting numbers are "C3AE-9431-D" (left) and "C2AE-
9430-B" (right). I do not believe they have ever been installed or run on a vehicle.  $1,000/obo.  Photos sent on request.  

SOLD!!!: 1963 ½ Galaxie 500 “Q” code Fastback. This is one of two cars I have and I decided I don’t want to build a number
correct car. After talking with Greg Donahue he told me there’s an obligation to build these cars correct and I hope I can pass that
obligation to a hopeful # correct Galaxie enthusiast. This is an original Q code So. Ca. car with no rust. Car has no engine or
headers but still has the original 4 speed in it with 4:11 rear end. The car is torn down for restoring and we have partially stripped
the 2nd paint job down to original paint. Glass is all very good and there is some body work required on both quarters (not rust
issues). Still a very straight and solid car. I do have all of the trim moldings and stainless which are all very good but the aluminum
parts need refinishing (no pitting), also a nice set of NOS emblems and badges. Interior is from another car and in excellent shape
but wrong color. Title is non-op and car comes with black plates. When I acquired the car its last registration sticker was Aug 1978,
it’s been stored inside since I’ve had it. I have plenty of pictures I can email. Car is listed in registry; you don’t see very many Q
codes for sale. Asking $7,000 I can hold the car for a while to find a good deal if shipping back east.

SOLD!!! 1965 full size Ford / Mercury 427 drivers side exhaust manifold. No sign of cracks or previous repairs… very nice part that
has been in storage for many years.  $650.00 + insured shipping from Va. 23093.  

SOLD!!! 1963-1/2 Ford Galaxie Original Lightweight car. Barn find. Sold new from Tasca Ford. Raced in the New England/Mid
Atlantic area until 1975 then parked. Great history,documentation and vintage pics. Very solid body and has all its original
Lightweight Ford parts included: Fiberglass Hood, decklid, inner fenders, has rare factory fiberglass doors too. Aluminum front/rear
bumpers with brackets, Bostrom bucket seats,Aluminum T-10 trans, scattershield,exhaust manifolds..Correct 427 engine is all ready
machined/assembled ready to go. Car is disassembled ready for a full body off resto. Frame has been stripped and blasted ready
for reassembly. Body is on dolly for easy transport. Asking 55K obo

FOR SALE:  1963-1/2 Lightweight Galaxie parts: Original fiberglass front end for a 1963-1/2 Lightweight Galaxie includes: Fenders,
Hood,Inner fenders.. one original aluminum front bumper bracket. Please contact

FOR SALE:  Aluminum T-10 trans for 1964 Lightweight or Thunderbolt..needs offer. Please contact amx1970@hotmail.

FOR SALE: 1963 Galaxie 427 C3AA-H transmission with stencil and Hurst Competition linkage and shifter box, the attachment point
for the shifter stick is broken . The gears have the groves on the vertical faces the gears and the syncros look great. I will crate the
transmission free but the shipping is the responsibility of the new owner $950 obo please contact via email or call 301-997-8799

SOLD!!! 1964 Galaxie 500 Fastback, factory "Q" code car, Rangoon Red, w/ White 500 XL interior, 4 speed toploader (BIG
IN/BIG OUT), 4.11-1 Detroit locker Nodular case 9 in.. Lakewood scattershield, clutch chatters slightly, has 1966 427 Sideoiler,
Low Riser heads, 410 horse intake, long cast iron manifolds. $19750.00     

WANTED:  Looking for a good used original 63-64 427 Dual Quad Low Riser Throttle Rod- connects the Bellcrank arm back to the
firewall rod. Email:

FOR SALE;  427 sideoiler block,  tunnelport heads, lemans rods, steel crank, single 4bbl intake manifold engine. The block,crank
and rods I can document that they were former Dick Trickle short track CWRA  pieces. Block is now at .015 over & will need to be
taken to .025 - .030. No sign of this being an exploded engine. $8500.00.  Can be contacted at 608 386 6036 noon till midnite CST
or E-mail

SOLD!!! 1964 Galaxie 500 XL  R code Convertible  This is a very solid car but currently has a 390 in it with the original cast iron
headers  & 4 speed. I have a 427  1963 block ,C3-d heads & dual 4 bbl intake & BJ - BK carbs to go with this. $37,500.00  

SOLD!!! 1963 Ford Galaxie R code 2 dr. boxtop, NO engine, needs restoration, have transferable registration, correct intake
manifold, carbs, linkage, fuel log, fuel filter canister, long tube cast iron headers, distributor, T- 10 with shifter also another T-10 in
pieces, all interior pieces, bucket seats, console with 4 speed plate, an extra set of perfect doors plus many other parts.

SOLD!!!: Borg/Warner T-10 4 Speed from a Ford 63' Galaxie Q Code 427. Factory groves cut into the gears for better lubrication
AS ON ALL 427’S. It was rebuilt and restored to NOS and is ready to install MINUS THE STENCIL. It comes complete as a "Drop-
In Unit" with correct date coded bell housing, shifter fork with dust boot, side cover and also a period correct Hurst Competition
shifter with all parts and shifter ball. $1500.00 plus you get the freight.

FOR SALE:  1960 - 63 NOS (not repro) original fan warning decals. I have a few @ $15 each shipped to US locations. Here is a
picture :   Tim O'Connor 10231 N  500 W  Wheatfield, In  46392  

FOR SALE:  1965 427 medium riser heads C5AE F NOS,with stainless steel valves installed and three angle valves job done. No
springs retainers or locks 2800.00 Steve 978 604 9819 or email

FOR SALE:  1966 427 medium riser side oiler has F weld on rear of block with 66-427 date code appears to be 61c no damage on
block was bored .030, ross 10.1 forged pistons,C5ae-c forge steel crank.lemans rods balanced assembly with new cam main and
connecting rod bearings,total seal chrome molly rings. assembled short block.7500.00 call steve 978 604 9819 email


FOR SALE: Ford 427 center oiler engine shortblock standard bore. C4AE-6015-B casting, 3J24 Block Date code, C4AE $ Steel
Crank standard rods and main journals, C3AE original rods, with pistons. Currently dissassembled, block has 1 sleeve. All bores are
very nice. No cracks or repairs on block. Comes with new cam, lifters and C3AE-9425-J Dual Quad manifold that is nice with no
cracks or repairs. No heads. Easy to finish and will make nice engine. $4800.00 Call 304-228-4732 or email

SOLD!!! 1963 Ford cast headers Left C3AE-9431-D,  right C2AE-9480-B. I bought these new 20 years ago and have never used
them. Was hoping to use them in my 1975 F-250 4x4 with a 427 top oiler but they won't fit in the truck. They would fit my 1965 427
side-oiler but have no car to put this setup into.

FOR SALE  1 pair of C5AE-F heads, one head dated Oct 66, the other dated Jan 67, one head was repaired $1000 obo. 1 pair of
C5AE-F heads dated 1970, one head needs repairing, $800 obo.  C5AE-H sideoiler block punched 15 but needs to be bored again
will have checked and find out how much more it needs to go.  One pair of cookie cutter valve cover caps stripped to bare steel
ready for re-chrome, $800 obo. Please contact

SOLD!!! 63 1/2 R-code 427 XL500 , very solid and complete car with still nice original black paint. Been in storage for many years.
390 in car at this time but has not ran for many years. I have the correct 427 for it but is disassembled. AM FM radio. Build sheet. E-
mail me for pics and details  

SOLD!!! 1964 Galaxie 500. For sale is the Legendary Ford Magazine project car known as Big Red. Less than 100 miles since a
total frame off restoration. This car was restored to be a great driver from a near basket case. It is not a 300 point "numbers
matching" show car. The engine is based on a 67 side oiler block, .030 over, custom forged Diamond pistons (10.5 compression)
steel crank, Low riser rods with ARP hardware, blue printed Melling oil pump, Comp Cams solid lifter cam and kit (Med. Riser
specs). C3AE-H low riser heads with Stainless steel M.R. valves. Upgraded to alternator, aluminum water pump, aluminum Griffin
radiator, 7 blade clutch fan. OE dual point distributor upgraded with electronics. Center Force flywheel / clutch assembly. Rebuilt
Big in / Big out top loader with Hurst shifter, OE 4.11 open rear. Auto Meter gauges. Chassis upgraded with poly bushings, larger
diameter front sway bar, 4 wheel disc brakes, police car wheels, radial tires. Body was totally stripped and all rusted areas
replaced with new steel. Rangoon red two stage paint, chrome and stainless professionally done. Interior is totally new re-pop red
vinyl. Custom  2 1/2" exhaust, Flowmaster mufflers and old school exhaust cutouts. Real R code Galaxie that looks, sounds and
drives great. $37500.00. Comes with build sheet and extensive 64 FoMoCo documentation. Photos available.  

WANTED: Air Cleaner FE Hipo style,Single carburetor, Chrome double hump open element style. Looks like this one>click here
email John @

FOR SALE:  1963 Galaxie cast headers Left C3AE-9431-D,  right C2AE-9480-B. Like new condition Asking $1250.00 Contact
Adam 503-307-3597

FOUND!!!: pair of Bostrum lightweight bucket seats, or name of company or individual that might have some or make some?  need
a set of black 6" flexible hose for cold air induction?

FOR SALE: 1960-64 Ford Galaxie/Mercury exhaust manifolds. Excellent condition, have not been on a car since I purchased them
in 1983. No broken tabs or cracks, only one stud broken (an easy replacement for you) Never blasted, stripped or painted. $350 M.
O. or PayPal + S/H to your zip (will quote on sale). Contact Bob @ Click here for pictures

FOR SALE: 1963 Ford 427 Engine  2 x 4 "R" code Very nice 427 with many features upgraded. The 427 was built as a reliable
hard running street engine. 1963 Ford engine UPGRADES: Melling Hi Vol, Cloyes True Roller,Bronze Guides,Hard Valve Seats,
Oversized Stainless Steel Valves ,Ported and polished Heads ,Blocked heat risers,and more. Pro Built very raspy 427
$12,000 obo Please contact Monterey CA.

SOLD!!! Early 60's FE short headers. Part numbers C1AE9431-C and C1AE9431-C. The right header has had two repairs. One
looks great the other will need some grinding/surfacing. These have been wire wheeled and sand blasted then painted with High
temp paint. The flange bolt threads seem ok but I have not put bolts in them. I'm asking $350 obo you pay shipping.

Wanted: In-dash clock for 1963 1/2 Ford Galaxie 500.  Must be working & in excellent shape.  Call (902) 794-3738 & ask for Bob
or e-mail me at

Wanted: Good Clean Used Pair of Rear Window Frames for 63 1/2 Fastback,Glass not required but I am willing to buy a set with
the Glass. Not looking for Frames to re-chrome,would prefer a set that can be cleaned up. Please contact Joe at

FOUND!!! Looking for a Good used C2 427 Harmonic Balancer. Not looking for something that needs rebonding.I will buy it or I
have a nice clean C4 Balancer that I could trade. Please contact Joe

SOLD!!!: 1962 Galaxie 406/405 tri-power 4 speed project car. Originally Oxford Blue with blue interior. The body work is done and
the car is in primer. All the hard to find parts are there. Would be an easy car to finish. I originally bought the car to finish for myself
but now it has to go. Asking $10,500 obo.

For Sale: This new soft rubber material with a high flow cotton element is washable and reusable. It measures 20.76 long x 9.75
wide x 2.50 tall. Will fit 427 (2 x 4) 390 &406 (3 x 2) This filter will improve air flow, mileage and increase horsepower.
$75.00 plus shipping. Contact Joe @  
Click here for pictures

SOLD!!!!: 427 Holley carbs # 2804 and 2805, recently set up and flowed by Quick Fuel Technology.  $700.00 for pair.

SOLD!!!! 1963 Galaxie 500XL 427 R code convertible. Fully restored with all the correct parts and date code correct. Painted in its
original color of Heritage Burgundy with a white convertible top. The interior is Rose Beige with white. Many NOS parts were used
throughout the car during restoration. There is way too much to list about this car so please call me with any questions

ALL PARTS SOLD!!!1963 Ford NOS PARTS. 1 voltage regulator #C3TZ-1050-B $50.00, 2 Bell Housing clutch fork Boots #C5TZ-
7513-A $25.00ea
BOTH SOLD. 2 Distributor point set for duel point distributor #B7A-12171-C $20.00 ea. BOTH SOLD,1 Backup
lamp kit pr. #C3AZ-15499-A3 $25.00, 1 Air cleaner filter for 2-4s $100.00
SOLD, RR Quarter panel still in primer never used for 63
1/2 fast back or convertible $1200.00 Lots of used 63 Galaxie parts to many to list.  

SOLD!!!!  1967 Ford Galaxie LTD real R code 427 425hp dual quad car. Marti report proves this car is 1 of 3 LTD's built in 1967,
and 1 of 1 in the color lime gold. Have original window sticker and purchase order. Purchased from original owner. Car has the
original black and yellow license plates. This car is the only 1967 LTD in the 427 Galaxie registry, and likely the only 1967 R code
LTD left in the world. This is your chance to own a real piece of fords performance history, this is the last year ford produced the
427 engine. Nice un-restored condition, with 1 re-paint. Black interior with comfort bench front seat,have the original steering wheel,
also have the original hubcaps brand new still in the original boxes. Car does have some rust behind rear window and some in rear
quarter panels,frame is clean,all glass is clean and all windows work nicely,dash is nice without any cracks,motor is real strong and
transmission shifts smooth. Clutch has no play and engagement is spot on. Engine compartment is really clean. All moldings on car
are nice and line up nicely and are dent free. Aside from the rust already mentioned the body is real straight and this car is in overall
very nice shape for it's age. Don't miss an opportunity to own a car that has a huge money making potential in the years to come!
Accepting serious offers!

SOLD!!!! 1964 Ford Custom, Factory "R Code" 427/425 Horsepower, Dual Quad, 2x4 Barrel Carburetors!Factory 4 Speed!!!
&  Extremely Rare!!! Low Original Miles!!! THE REAL DEAL!!!

Phidon Restorations is offering fully restored Rotunda and Sun tachometers along with factory clocks that are 100% correct for your
Click here for more information or contact Phil Severance at 1-208-734-4535. You can also visit his website:

For Sale: Correct FA-46 replacement air filters for 427 Ford Galaxie. Our filters measure 2.25" tall The only other paper
replacement available is 1.75" tall. Our filters are the correct cream colored paper and were reproduced from an NOS filter for the
correct dimensions. In stock and ready to ship. $124.95 + $20.00 shipping and insurance.
Click Here for pictures Contact:
Mikes Classic Cars at 402-533-4667 or on the web at

Ford Yellow Top Coil Restoration Service: Have your original Ford coil restored or buy a brand new one with all the correct
stampings and date coded to your car.
Click Here for more information...FOR
This is the perfect place to advertise your rare Hipo Galaxie and Ford parts, cars or items your looking to sell or buy.
Your also welcome to list any other items for sale as long as they are automotive related.
Your email will be used as your contact information unless you specify otherwise.
Factual accuracy of the ads placed here are the sole responsibility of the seller.